Assessment of pharmacokinetic interaction between piracetam and l‐carnitine in healthy subjects

A rapid, sensitive and specific method for quantifying piracetam in human plasma using Piracetam d‐8 as the internal standard (IS) is described. The analyte and the IS were extracted from plasma by one‐step precipitation of protein using an acetonitrile (100%). The extracts were analyzed by high‐performance liquid chromatography coupled with electrospray tandem mass spectrometry (HPLC‐MS/MS). The method had a chromatographic run time of 3.8 min and a linear calibration curve over the range 0.5–50 µg/mL (r > 0.99). This LC‐MS‐MS procedure was used to assess the bioavailability of two piracetam formulations: piracetam + l‐carnitine (Piracar®; 270/330 mg tablet) and piracetam (Nootropil®; 800 mg tablet) in healthy volunteers of both sexes. The geometric means with corresponding 90% confidence interval (CI) for test/reference percentage ratios were 88.49% (90% CI = 81.19 – 96.46) for peak concentration/dose and 102.55% (90% CI = 100.62 – 104.51) for AUC_inf/dose. The limit of quantitation of 0.5 µg/mL is well suited for pharmacokinetic studies in healthy volunteers. It was concluded that piracetam (Piracar®; 270/330 mg tablet) has a bioavailability equivalent to the piracetam (Nootropil®; 800 mg tablet) formulation with regard to both the rate and the extent of absorption. Copyright © 2015 John Wiley & Sons, Ltd.     

Replacing Synthetic with Microbial Surfactants as Collectors in the Treatment of Aqueous Effluent Produced by Acid Mine Drainage,Using the Dissolved Air Flotation Technique

Dissolved air flotation (DAF) is a well-established separation process employing micro bubbles as a carrier phase. The application of this technique in the treatment of acid mine drainage, using three yeast biosurfactants as alternative collectors, is hereby analyzed. Batch studies were carried out in a 50-cm high acrylic column with an external diameter of 2.5 cm. High percentages (above 94%) of heavy metals Fe(III) and Mn(II) were removed by the biosurfactants isolated from Candida lipolytica and Candida sphaerica and the values were found to be similar to those obtained with the use of the synthetic sodium oleate surfactant. The DAF operation with both surfactant and biosurfactants, achieved acceptable turbidity values, in accordance with Brazilian standard limits. The best ones were obtained by the biosurfactant from C. lipolytica, which reached 4.8 NTU. The results obtained with a laboratory synthetic effluent were also satisfactory. The biosurfactants removed almost the same percentages of iron, while the removal percentages of manganese were slightly higher compared with those obtained in the acid mine drainage effluent. They showed that the use of low-cost biosurfactants as collectors in the DAF process is a promising technology for the mining industries.     

Characterization of nanochannel delivery membrane systems for the sustained release of resveratrol and atorvastatin: new perspectives on promoting heart health

Novel drug delivery systems capable of continuous sustained release of therapeutics have been studied extensively for use in the prevention and management of chronic diseases. The use of these systems holds promise as a means to achieve higher patient compliance while improving therapeutic index and reducing systemic toxicity. In this work, an implantable nanochannel drug delivery system (nDS) is characterized and evaluated for the long-term sustained release of atorvastatin (ATS) and trans-resveratrol (t-RES), compounds with a proven role in managing atherogenic dyslipidemia and promoting cardioprotection. The primary mediators of drug release in the nDS are nanofluidic membranes with hundreds of thousands of nanochannels (up to 100,000/mm²) that attain zero-order release kinetics by exploiting nanoconfinement and molecule-to-surface interactions that dominate diffusive transport at the nanoscale. These membranes were characterized using gas flow analysis, acetone diffusion, and scanning and transmission electron microscopy (SEM, TEM). The surface properties of the dielectric materials lining the nanochannels, SiO₂ and low-stress silicon nitride, were further investigated using surface charge analysis. Continuous, sustained in vitro release for both ATS and t-RES was established for durations exceeding 1 month. Finally, the influence of the membranes on cell viability was assessed using human microvascular endothelial cells. Morphology changes and adhesion to the surface were analyzed using SEM, while an MTT proliferation assay was used to determine the cell viability. The nanochannel delivery approach, here demonstrated in vitro, not only possesses all requirements for large-scale high-yield industrial fabrication, but also presents the key components for a rapid clinical translation as an implantable delivery system for the sustained administration of cardioprotectants.     

Assessment of dispersive liquid–liquid microextraction for the simultaneous extraction,preconcentration, and derivatization of Hg2+ and CH3Hg+ for further determination by GC–MS

This work reports the development of a dispersive liquid – liquid microextraction method for the simultaneous extraction, preconcentration, and derivatization of Hg²⁺ and CH₃Hg⁺ species from water samples for further determination by GC – MS. Some parameters of the proposed method, such as volume and type of disperser and extraction solvent, and Na[B(C₆H₅)₄] concentration were investigated using response surface methodology. Suitable recoveries were obtained using 80 μL C₂Cl₄ (as extraction solvent), 1000 μL ethanol (as disperser solvent), and 300 μL 2.1 mmol/L Na[B(C₆H₅)₄] (as derivatizing agent). Accuracy was evaluated in terms of recovery and ranged from 87 to 99% with RSD values <7%. In addition, a certified reference material of water (NIST 1641d) was analyzed and agreed with the certified value about 107% (for Hg²⁺), with RSD values <8.5%. LODs were 0.3 and 0.2 μg/L, with enrichment factors of 112 and 115 for Hg²⁺ and CH₃Hg⁺, respectively. The optimized method was applied for the determination of Hg²⁺ and CH₃Hg⁺ in tap, well, and lake water samples.     

Development and validation studies for determination of phenylpropanoid‐substituted flavan‐3‐ols in semipurified extract of Trichilia catigua by high‐performance liquid chromatography with photodiode array detection

The phenolic compounds are the main phytochemical constituents of the bark of Trichilia catigua and are commonly used for medicinal purposes. An HPLC method for the simultaneous quantification of phenolic compounds (procyanidin B2 (PB2), epicatechin (EPC), chinchonains Ia, Ib, IIa, IIb, catechin, and chrologenic acid) in T. catigua extract was developed and validated. A suitable chromatographic system was selected, which uses a gradient elution with methanol/ACN (75:25), and water both with 0.05% TFA, as mobile phase, column Luna, 280 nm, and flow 0.4 mL/min. Validation of the analytical method was based on the parameters: linearity, precision, LODs and LOQs, accuracy, robustness, and stability. The method showed linearity for PB2 and EPC, in the range 10–120 μg/mL with good correlation coefficients (>0.996). For precision, the repeatability ranged from 1.89 to 3.23%, and the values for accuracy for PB2 and EPC were 95 and 89%, respectively. The LODs and LOQs for PB2 were 1.36 and 4.12 μg/mL, and for EPC were 2.18 and 6.61 μg/mL, respectively. The method was robust under the conditions employed. The proposed method could be employed for quality assessment of T. catigua, as well as pharmaceutical products.     

From Levulinic Acid to Biheterocycles: Synthesis of 1-[(5-Hydroxy-5-trifluoromethyl-3-substituted-4,5-dihydro-1H-pyrazol-1-yl)-3-(5-trifluoromethyl-1H-pyrazol-3-yl)propan-1-ones

We develop an efficient method to synthesize novel propionyl-spaced bisheterocyclic compounds. It entails cyclocondensation of 3-(5-trifluoromethyl-1H-pyrazol-3-yl)propanoyl hydrazide obtained from levulinic acid, with 1,1,1-trifluoro-4-methoxy-3-alken-2-ones proceeding regiospecifically to 1-[(5-trifluoromethyl-5-hydroxy-3-substituted-4,5-dihydro-1H-pyrazol-1-yl)-3-(5-trifluoromethyl-1H-pyrazol-3-yl)propan-1-one derivatives.     

Contribution of CuxO distribution,shape and ratio on TiO2 nanotubes to improve methanol production from CO2 photoelectroreduction

Many studies are focused on the development of materials for converting carbon dioxide into multicarbon oxygenates such as methanol and ethanol, because of their higher energy density and wider applicability. In this work, TiO₂ nanotubes (NT/TiO₂) were modified with Cu_xO nanoparticles in order to investigate the contribution of different ratio of Cu₂O/CuO and its distribution over NT/TiO₂ for CO₂ photoelectro-conversion to methanol. The photoelectrodes were built by anodization process to obtain NT/TiO₂ layer, and the decoration with Cu_xO hybrid system was carried out by electrodeposition process, using Na₂SO₄ or acid lactic as electrolyte, followed by annealing at different temperatures. X-ray photoelectron spectroscopy analysis revealed the predominance of Cu⁺¹ and Cu⁺² at 150 °C and 300 °C, respectively. X-ray diffraction and scanning electron microscopy indicated that under lactic acid solution, the oxide nanoparticles exhibited small size, cubic shape, and uniform distribution on the nanotube wall. While under Na₂SO₄ electrolyte, large nanoparticles with two different morphologies, octahedral and cubic shapes, were deposited on the top of the nanotubes. All modified electrodes converted CO₂ in methanol in different quantities, identified by gas chromatograph. However, the NT/TiO₂ modified with CuO/Cu₂O (80:20) nanoparticles using lactic acid as electrolyte showed better performance in the CO₂ reduction to methanol (0.11 mmol L⁻¹) in relation to the other electrodes. In all cases, a blend among the structures and nanoparticle morphologies were achieved and essential to create new site of reactions what improved the use of light irradiation, minimization of charge recombination rate and promoted high selectivity of products.

     

Tailoring a Zinc Oxide Nanorod Surface by Adding an Earth-Abundant Cocatalyst for Induced Sunlight Water Oxidation

Herein, a detailed investigation of the surface modification of a zinc oxide (ZnO) nanorod electrode with FeOOH nanoparticles dispersed in glycine was conducted to improve the water oxidation reaction assisted by sunlight. The results were systematically analysed in terms of the general parameters (light absorption, charge separation, and surface for catalysis) that govern the photocurrent density response of metal oxide as photoanode in a photoelectrochemical (PEC) cell. ZnO electrodes surface were modified with different concentration of FeOOH nanoparticles using the spin-coating deposition method, and it was found that 6-layer deposition of glycine-FeOOH nanoparticles is the optimum condition. The glycine plays an important role decreasing the agglomeration of FeOOH nanoparticles over the ZnO electrode surface and increasing the overall performance. Comparing bare ZnO electrodes with the ones modified with glycine-FeOOH nanoparticles an enhanced photocurrent density can be observed from 0.27 to 0.57 mA/cm² at 1.23 V_RHE under sunlight irradiation. The impedance spectroscopy data aid us to conclude that the higher photocurrent density is an effect associated with more efficient surface for chemical reaction instead of electronic improvement. Nevertheless, the charge separation efficiency remains low for this system. The present discovery shows that the combination of glycine-FeOOH nanoparticle is suitable and environmentally-friend cocatalyst to enhance the ZnO nanorod electrode activity for the oxygen evolution reaction assisted by sunlight irradiation.     

Experimental Evidence of CO2 Photoreduction Activity of SnO2 Nanoparticles

Tin dioxide (SnO₂) has intrinsic characteristics that do not favor its photocatalytic activity. However, we evidenced that surface modification can positively influence its performance for CO₂ photoreduction in the gas phase. The hydroxylation of the SnO₂ surface played a role in the CO₂ affinity decreasing its reduction potential. The results showed that a certain selectivity for methane (CH₄), carbon monoxide (CO), and ethylene (C₂H₄) is related to different SnO₂ hydrothermal annealing. The best performance was seen for SnO₂ annealed at 150 °C, with a production of 20.4 μmol g⁻¹ for CH₄ and 16.45 μmol g⁻¹ for CO, while for SnO₂ at 200 °C the system produced more C₂H₄, probably due to a decrease of surface −OH groups.